|
Search:
Type: Posts; User: SZR
Search:
Search took 0.01 seconds.
-
Gangus,
Notice the replate instructions I gave in the second photo, "crack not welded as instructed".
If you weld up this crack at time of replate it will only quickly crack again with...
-
-
SOLD
Sorry to those that missed out, my PM inbox did not notify me by email and people were left waiting for response. These are now sold to the first PM received in order.
Cheers,
Sam
-
It pains me to sell these as I bought them brand new and only ever used for about 5-8 pulls on the dyno before I prematurely stopped the development my 5KE. Sadly that's all they have been used and...
-
Purchased brand new from Japan in 2009, this cylinder has had little use from new and has been replated once only in 2010. No welding repair just simple replate to the cylinder, not used since....
-
Or fit your very own interface plugs in between, this way you can easily 'plug and play' between any ignition of choice into your loom within seconds.....just have your base advance software settings...
-
The problem in the image below was a dodgy kill switch on an RS250.
If the logger shows jaggered lines for RPM then there is no spark, not weak spark, fuel or engine setup.
Just saying...........
-
If it has a engine kill switch fitted, my money is on that.
By pass the kill switch, I'm sure all will be good after that.
-
Check the barrel shaped condenser is plugged into the loom. (green/red wire) Sounds like the stator can't provide enough power to run the PCM at high power surge / RPM due to a missing...
-
I've seen a couple of cases recently where some near new 5KE pistons have broken it's crown a piece about 1/8 of it's crown starting from one side of where the ring pin locating dowel is. It's as if...
-
FOR SALE
2003 onwards TZ250 powervalve side covers.
These covers are very EXPENSIVE from Yamaha.
Current YAMAHA Prices are;
5KE-1131X-00 approx USD 320.00 each
5KE-1131F-00 approx USD 290.00...
-
Thanks Vince.
I've never had a tab break off but if you seen this happen due to fatique over time, I better also be careful in future. I normally have a tendancy to over tighten and/or re-tigthen...
-
I think that you did not mesh in the inner centre gear that drives the oil pump gear by turning the clutch basket/primary drive gear as your putting the cover on. This means that the side cover looks...
-
I was just working on a 4DP engine this morning and it has cast on the cases between the top reed block and barrel 3XV-02, however where the engine serial number is located on the cases above the...
-
I can't read Japanese and did not understand the sloped line for powerjet transistion so I logged my PJ's for the +2003 TZ250 ignition with kit setup.
I logged both top and bottom powerjets at...
-
3XV01 = 1991 TZR250R
This is a street bike, not a TZ250.
-
All TZ's from about 93 onwards till today has the wire Black/white wire.
If you short this wire to ground it will turn off the engine. This is where Yamaha recommend you put an aftermarket...
-
5KE has an extra steel and lining over the 4TW/4DP.
This means the basket and hub have to be made longer.
The 5KE springs are different also.
5KE uses 5 steels, 2 outers and 4 inner linnings...
-
I'm after the cylinder for an RS500 TWIN cylinder version.
Any condition considered.
PM me if you have.
Thanks
-
Caltk,
I'm after a cylinder for an RS500 TWIN cylinder version if you have or know of one available. Any condition considered.
PM me if you have.
Thanks
-
Hi Neil,
What does the bearing sound like when you spin it on the drive side? Is it noisey when comparing to the clutch side bearing?
The drive side bearing only has 1 oiling hole compared to the...
-
A picture of an RS250 to be sure...... http://www.tz250racing.com/iB_html/non-cgi/emoticons/smile.gif
http://www.samzavaglia.com/RS250.jpg
-
SOLD....thanks for looking
-
Price Reduction.
US$500 or AU$600
4-7 days Postal Service anywhere in the world included in price.
-
For Sale
VHM +2003 TZ250 heads and inserts
AA33065 Cylinder Head Set TZ250 +2003
AE32080-052 11.6cc insert x2
AE32080-009 11.8cc insert x2
http://www.samzavaglia.com/VHM1.JPG
...
|
<% COPYRIGHT %> |
|
|
|